Activity 4: Example for rate analysis of an item

By -
Rate Analysis

Item: Wiring for 6A (3 Pin) & 16 A (6 pin)socket outlet point  in heavy guage PVC casing with 4 Sq.mm wires & 4 Sq.mm insulated earth wire complete with switches & socket outlets in one box.
A Short point up to 3 meters
Sl.No Description Unit  Qty Rate (Rs) Amount (Rs) Remarks
1 Wiring with 3×4 Sq.mm single core copper cable in suface heavy guage PVC casing meter 3 188.3 564.93 DSR 2013 item No 1.12 +13.5%×0.75% VAT (171+17.31=188.31)
2 200mm×125mm×60mm metal box No 1 51.54 51.54 DSR 2013 item No 1311+13.5%×0.75% VAT(46.8+4.74=51.54)
3 3 mm thick phenolic laminated sheet sq.cm 250 0.1 25 Adopted from DSR 2013 item No 1322 + 13.5%×75% VAT (0.09+0.009=0.10)
4 Supplying & fixing 3 pin 5/6A socket outlet on existing  switch box including connections each 1 41.85 41.85 Adopted from DSR 2013 item No 1.23.4 + 13.5%×75% VAT  (38+3.85=41.85)
5 Supplying & fixing 5/6A switch on existing  switch box including connections each 1 35.24 35.24 Adopted from DSR 2013 item No 1.23.1 + 13.5%×75% VAT (32+3.24=35.24)
6 Supplying & fixing 6  pin 15/16A socket outlet on existing  switch box including connections each 1 82.59 82.59 Adopted from DSR 2013 item No 1.23.5 + 13.5%×75% VAT (75+7.59=82.59)
7 Supplying & fixing 15/16A switch on existing  switch box including connections each 1 70.48 70.48 Adopted from DSR 2013 item No 1.23.3 + 13.5%×75% VAT (64+6.48=70.48)
Total 871.63
say 872







Comments

Post a Comment

Popular posts from this blog

Multiple Choice Questions in Power Electronics - 1

By -
  Important multiple choice questions from Power Electronics 1.       Which one of the following statements is not correct? a)       Power MOSFETs are so constructed as to avoid punch through. b)       In a power MOSFET, the channel length is relatively large and channel width is relatively small c)       Power MOSFETs do not experience any minority carrier storage d)       Power MOSFETs can be put in parallel to handle large currents 2.       Which one is most suitable power device for high frequency (>100 kHz) switching application? a)       Power MOSFET b)       BJT c)       Schottky diode d)       Microwave transistor 3.       A thyristor equivalent of thyratron tube is a)       SCR b)       UJT c)       Diac d)       Triac 4.       Turn-on of thyristor takes place when a)       Anode to cathode voltages is positive b)       Anode to cathode voltages is negative c)       There is a positive current pulse at the gate d)       The
Read more

Multiple Choice Questions on Power System - 3

By -
Important multiple choice questions on power system 1.        A line trap in carrier current relaying tuned to carrier frequency presents A)      High impedance to carrier frequency but low impedance to power frequency B)       Low impedance to both carrier and power frequency C)       High impedance to both carrier and power frequencies D)      Low impedance to carrier frequency and high impedance to power frequency 2.        The use of fast acting relays and circuit breakers for clearing a sudden short circuit on a transmission link between generator and the receiving end bus improves the transient stability of the machine because A)      Short circuit current becomes zero B)       Post-fault transfer impedance attains a value higher than that during the fault C)       Ordinate of the post-fault power-angle characteristic is higher than that of during fault characteristic D)      Voltage behind the transient reactance increases to a higher value 3.        A
Read more

Multiple choice questions on Power Systems- 4

By -
Important Multiple Choice Questions On Power Systems 1. With 100 % inductive shunt compensation, the voltage profile is flat for 100% loading line 50% loading line Zero loading of line None of these 2. For a long uncompensated line the limit to the line loading is governed by Thermal limit Voltage drop Stability limit Corona loss 3. Series capacitive compensation in EHV transmission lines is used to Reduce the line loading Improve   the stability of the system Reduce the voltage profile Improves the protection of the line 4. The main consideration for higher and higher operating voltage of transmission is to Increase the efficiency of transmission Reduce power losses Increase power transmission capability Both (A) and (B) above 5. The inertia constant H of a machine of 200MVA is 2 p.u. its value corresponding to 400MVA will be 4 2 1 0.5 6. A 500MVA, 11kV synchronous generator has 0.2 p.u. synchronous re
Read more